trusted seller

Civil Engineering Lab Equipments

Our wide assortment of Civil Engineering Lab Equipments has extensive utilizations in educational institutes and scientific research laboratories for its ergonomic design. Durable metals like stainless steel or brass has been used to design these lab equipments. Stainless steel made Core Cutter offered under this category of products is used for measuring dry density level of aggregate free soil on the basis of moisture content and weight of soil. The operating principle of GPS receiver offered as a part of Civil Engineering Lab Equipments depend on trilateration mathematics theory to determine the location of GPS satellites.

Product Image (MT-298QAM)

Automatic Quartz Water Distillation Equipment Cabinet

Price: 100 INR/Piece

This is a Fully Automatic Water Distillation Equipment and can be used in research laboratories, hospitals etc. It is manufactured from 3.3 exp Borosilicate Glass or Quartz Glass. The distillation has following features: Replaceable Silica Sheathed (Quartz) Heater: The Horizontal Jacket is fitted with removable Silica Heater and Screw Threaded Connectors for ease of cleaning. Distillate temperature is around 25 to 45 degree C which is ensured by an efficient condenser. The stand is powder coated for rust free operation and lustrous appearance. Cooling water from the condenser is re-circulated into the boiling chamber, hence saving energy. Screw Threaded Connectors: These are provided for easy Plumbing & Installation to avoid any glassware breakage during assembly. Fuse is provided for safety in case of voltage fluctuation or short circuit. Boiler is provided with a Replaceable Side over Flow for easy draining and cleaning of boiling chamber. The front cover is removable for checking the glass parts. Electrical Power: 220/240 V, 50/60Hz, Single Phase AC Supply.

Product Image (MTSE-60)

Plane Table

Price: 100 INR/Piece

Plane Table Heavy duty ground plate setting up of leveling staff.

Product Image (MTSE-08D)

Total Station

Price: 1000 INR/Piece

Total Station Telescope Fully transiting, coaxial sighting and distance measuring optics Objective aperture:45mm(1.8in) (EDM:50mm)(2.0in) Magnification:30x Image :Erect Resolving power:3" Field of view:130" (26m/1,00m) Minimum focus:1.0m(3.3ft) Reticule illumination: built bright/Do. Select-able Focusing ring : Fine/ coarse two speeds ANGLE MEASUREMENT Photoelectric incremental rotary encoders scanning. both circles adopt diametrical detective and are provided with absolute 0 index points.

Product Image (MTSE-44)

Survey Umbrella

Price: 100 INR/Piece

Survey Umbrella In water proof cotton Diameter of the pole 25 mm With two guy ropes &pegs

Product Image (MTSE-55)

Spirit Level

Price: 10 INR/Piece

Spirit Level Aluminum alloy, two adjusting bubble length 1200mm

Product Image (MTSE-51)

Walky Talkie

Price: 100 INR/Piece

Walky Talkie Digital Display+ frequency mode Equivalent PUXING PX-777 PLUS UHF (400-470MHz)

Product Image (MTSE-01A)

AUTOMATIC LEVEL

Price: 8 INR/Piece

AUTOMATIC LEVEL Telescope Length:2/5mm(8.5 in) Objective aperture:42mm (8.5in) Magnification:32x Image:Erect Resolving power:76mm (3") Minimum focus:1m Field view:100 20(2.3m) Stadia multiplication constant:100 Reticule illumination:illuminator One speed focus:standard Sunshade:Standard

Product Image (MTSE-36)

Teknik Prisms

Price: 100 INR/Piece

Prisms Square Two primes90 Œ and 180 Œ SIZE:4 inches FLATNESS:flat to¼wave length of sodium light PARALLELISM:parallel to±5 minutes of arc deviation EDGES:straight cut angular, beveled, glazed, fire polished ANGLES:angular tolerances to±5 seconds of arc deviation FINISHES:free from surface imperfections when viewed under 10X magnification

Product Image (MTSE-32)

Range Pole

Price: 9 INR/Piece

Range Pole Material:aluminum, Length:2mlong Diameter:30mm dia

Product Image (MTSE-41)

Plumb Bobs

Price: 100 INR/Piece

Plumb Bobs Metal top plate and point, Bright turned finish, brad knob Approx Weight. 400g. Made of brass

Product Image (MTSE-49)

Triangular Scale (Engineering Scale)

Price: 10 INR/Piece

Triangular Scale (Engineering Scale) With dimensionally stable plastic. The precision divisions are numerated both ways. Dimension making in cm and m easier working with two colored. Sizes:1/10,1/20,1/50,1/100,1/125,1/200,1/250,1/500

Product Image (MTSE-30)

Pocket Stereoscopes

Price: 10 INR/Piece

Pocket Stereoscopes Magnification is 4x With good field of view and optical path Distance b/n lenses:adjustable from 56cm to 75cmStrong ABS frames, high quality crown glass lenses Stainless steel leg Include a durable protective sleeve Include soft carrying case.

Product Image (MTS-201KA)

Multipurpose Material Testing System

Price: 99 INR/Unit

MULTIPURPOSE MATERIAL TESTING SYSTEM (CMT-20 Computer Control Electronic Universal Testing Machine) PC Universal Measure Tensile Strength Testing Instrument/Tensile Testing Machine with Computer and Printer Test operation and data processing meet the following requirements of test method to analysis Tensile Test Method Compression Test Metals and Nonmetallic material (including composite material)Compression Test Bending Test Shear Test It has achieve REH, REL, Rp0.2, Fm, Rt0.5, Rt0.6, and Rt0.65, Rt0.7, Rm, E and other testing parameters automatically and can also do test and provide data according to GB, ISO, DIN, ASTM, JIS and other international standards.

Product Image (MT-831)

Hardness Measurement

Price: 5 INR/Unit

PORTABLE HARDNESS MEASUREMENT Shl-160 portable hardness tester (accurate measurement for metal). Hardness System:Leeb, Brinell, Rockwell a, Rockwell B, Rockwell C. Continuous Working Time:About 100 Hours. Limit Setting Range:Same as Measurement Range. Ambient Temperature:040C Communication Interface:Standard USB2.0. Display:O LED, 128”32 Graphics DOT Matrix LCD. Battery:3V, (1200mAh). Accessories:With all necessary accessories.

Product Image (MT-802B)

Digital Display Brinell Hardness Tester

Price: 100 INR/Unit

Digital Display Brinell Hardness Tester Measuring range:8-650HBW Test force:187.5kgf (1839N), 250kgf (2452N), 500kgf (4903N),750kgf (7355N), 1000kgf (8907N), 1500kgf (14710N), 3000kgf (29420N) Max. height of test piece:230mm Head center to machine wall distance: 135mm Power supply:220V AC Dimensions:700 x 270 x 840mm Weight:Approx. 150kg With all necessary accessories

Product Image (MT-829C)

Thermal Dilatometer Ceramic Laboratory Equipment

Price: 5 INR/Unit

Thermal Dilatometer Ceramic Laboratory Equipment

Product Image (MT-802)

Hardness Measurement

Price: 5 INR/Unit

Hardness Measurement Brinell Indentation Measurement System/Universal Hardness Tester /Brinell Hardness Test/Hardness Tester /Metal Hardness Tester/Brinell Durometer/Durometer. Loads:250 to 3000 in stages of 250 kgf Max. test height:380mm

Product Image (MTS-807A)

Automated Fraass Breaking Point

Price: 100 INR/Unit

Technical specifications: Power supply:AC(220 less or more 10%)V,50Hz Refrigeration mode:Low temperature circulatory bath Cooling rate:(1 less or more 0.5) degree C/min Temperature measuring range:-30 degree C25 degree C Temperature measuring error: less or more 0.5 degree C Steel slice:41mm * 20mm* 0.15mm Test samples:It has determined 3 samples at the same time. Ambient temperature:Room temp. approx 30C Relative humidity:less then or equal to be 85% Power consumption:450W(breaking point tester)+ 1600W(low temperature circulatory bath) Overall dimension:500mm * 400mm * 570mm(approx)

Product Image (MTBA-27A)

Automatic Digital Bitumen Penetrometer

Price: 100 INR/Unit

AUTOMATIC DIGITAL BITUMEN PENETROMETR Dimensions:270 x 480 x 750 mm Measuring Range:0-50 mm Power:75 W Resolution:0.01 mm Test Load:100 g (plunger 97.5 g + 2.5 g penetration needle) Test Time:5 seconds (adjustable from 0.1 to 9999 sec.) Weight (approx.):24 kg Description The Automatic Electronic Penetrometer is used for determination of the needle penetration according to EN 1426, ASTM D5 and AASHTO T49 standards. The penetration depth of the needle is determined with a pulse type electronic measuring system, which is separated from the plunger during the test; this allows the free guidance of the plunger which virtually eliminates friction during the test. Before each start of the test the measuring system automatically resets, and then the penetration needle moves down to the sample by using the electric drive, the needle position can be finely adjusted by using the joystick located on the front panel. A magnifying glass and an ultra- bright LED lamp are supplied to assist the operator; the plunger is then automatically released onto the sample and raised automatically after the testing period. The test result is displayed on the digital display. The plunger can easily be removed to calibrate its weight. The Automatic Electronic Penetrometer is supplied complete with: Penetration Needle Transfer Dish Sample Cup, 55x35 mm, 6 pieces, stainless steel EN 1426; ASTM D5; AASHTO T49

Product Image (MTS-812A)

Ductilometer The Elastic Recovery

Price: 100 INR/Unit

Ductilometer The Elastic Recovery Power supply:AC220V(-5%+10%),50Hz Measurement distance:1.5m(±10mm) Heating mode:Electric heater Heating power:3000W Liquid circulation:By magnet circulation pump Temperature control range:(549) ž, adjustable. Resolution:0.01ž Temperature control accuracy:±0.1ž. Tensile speed:10mm/min and 50mm/min, two grades Measurement accuracy:±1 mm. Ductility display:Digital display after data processed by a single chip machine. Refrigeration:Compressor 1.25P, input power is 950W. Ambient temperature:(-10+35)ž Relative humidity:85% Maximum power consumption:4100W Overall dimension:2365mm”520mm”1000mm

Product Image (MTBA-27A)

Teknik Penetrometer

Price: 100 INR/Unit

Penetrometer Cast iron base with leveling screws, digital penetration measurement gauge 0.01 mm precision, release button, automatic zeroing. Semi-automatic is supplied complete with automatic controller, which automatically releases the plunger by a magnetic device. Both models are fit with a micrometer vertical adjustment device. The electronic timer allows the user to set up and read the fall time of the needle during testing. Conforming to ASTM D217

Product Image (MTS-803A)

Wheel Tracking

Price: 100 INR/Unit

Wheel Tracking Specification: The machine fully satisfies both EN 12697-22 and BS 598:110 Specifications Travel of the table : 230 /- 5 mm Table cycle frequency : adjustable 15 to 40 cycles per minute Hard rubber tyred wheel having outside diameter 200 mm Wheel load on the sample : 700N /-10N (EN 12697-22) or 520N (BS598:110). The load is applied on the sample through a lever The effective load applied on the sample adjusted by micrometrical weights positioning Continuous real time rut depth measurement (penetration of the wheel into the sample) through a linear transducer 40 mm travel by 0, 01 mm accuracy. The test frame is made of robust aluminum alloy and it is contained in a climatic cabinet with adjustable temperature from 30 to 65C. /- 1.0C. The cabinet is equipped with two doors with insulated glass for inspection The sample table has dimensions: 400 x 390 mm and can accept rectangular slabs of several sizes: 305 x 305 mm, 50 or 100 mm high 305 x 400 mm, 50 or 100 mm high 200 mm dia. core samples, 50 mm high The sample confinement frames are not included and ordered separately (see accessories) Also accepts samples with dimensions up to 400 x 500 mm, 180 mm high The machine is supplied complete with adaptors for a correct mould positioning and locking The wheel tracker is equipped with 3 temperature probes 1 Probe, connected to the thermo regulator, for the control and adjustment of the cabinet temperature 2 Probes for temperature measurement inside the specimen Hardware: Data acquisition and processing system fully managed by microprocessor Multi functions keyboard with encoder for easy and rapid setup Large graphic display 320 X 240 pixel RS 232 port for connection to PC Firmware: The multilingual testing firmware allows Management and automatic control of machine and test Setup of all test parameters Test data acquisition and processing Real time display of: number of cycles, rut depth, temperatures. Real time cycle rate will also be displayed when using a serial connection to PC Calibration menu for setting and checking all test data From the control board, it is possible to select parameters, set data acquisition and processing according to EN and BS test procedures, with Identification data of the sample (slab) under test Cycle frequency Number of passes to end the test Max rut depth to end the test Sampling frequency of the rut depth Testing temperature Sample (slab) thickness The use of the B038 Wheel Tracker requires connection to a PC with Windows 98, 2000, XP minimum requirements. Power supply: 230 V 50/60 Hz 1 ph 2200 W Power rating of the table : 500 W Dimensions: 1580 x 650 X H 1790 mm Weight: 400 kg approx

Product Image (MTBA-25B)

Ring And Ball Automatic Softening Point

Price: 100 INR/Unit

Ring And Ball Automatic Softening Point Technical Specifications: Temperature measurement range:0-180ž Test range:5-90ž Three heating rate:5 ±0.5ž / min Heating method:heating speed PID control and fuzzy logic algorithm, magnetic stirring. Detection way:automatic test. Steel ball quality:3.5 g± 0.05 g Ball diameter:9.53 mm. Ball sinking:25.4 mm. Rings:JTG E52 standard - 2011 procedures. Timing range:0-99m 99s Temperature measuring accuracy:0.1ž Standards:GB/T4505, ASTMD36, T0606-2011. Dimensions:340 x230x340mm (Approx) Weight:4.5 KG Voltage:220 v; Power: 1 kw Environment temperature:5 40ž Environmental humidity:< 85 percent

Product Image (MTBA-27C)

Fully Automatic Universal Penetrometer

Price: 100 INR/Unit

Fully Automatic Universal Penetrometer Display Type : Digital Material:Stainless Steel Diameter :220x400x550 mm Voltage (V) :240V Frequency (MHz):50 / 60 HZ Phase:Single Phase Accuracy (%):-2% Weight:16 kg

Product Image (MTS-810)

Digital Universal Testing Machine

Price: 100 INR/Unit

DIGITAL UNIVERSAL TESTING MACHINE (THREE POINT BENDING)

Product Image (MTAT-04)

Sieve Shaker Electromagnetic

Price: 100 INR/Unit

Sieve Shaker (Electromagnetic) This Sieve Shaker uses electromagnetic impulses to impart a triple vibrating action. Vertical Lateral Rotational The shaker is of a simple and sturdy construction making it ideal for continuous and intense use. It is operated and controlled via a separate control panel enabling high precision, performance and repeatability. It is fitted with a digital 1 to 999 minute timer, accessed through the digital control panel. This separate panel also gives the user control of the vibration intensity and pauses between sieving actions, which is particularly useful when sieving fine materials. Note:- Wet sieving kits in the appropriate sizes may be used with this shaker. Features Tri-dimensional sifting motion 2 modes of sifting Low maintenance Isolation of vibrations from work surface Particle size analysis Programmable amplitude Programmable sieving duration Larger LCD Low noise Programmable shake time from 1 min to 99 mints Ideal for particle size analysis and separation Intermittent and continuous shifting motion with 15 program amplitude Suitable for dry and wet sieving Technical Specification Digital control panel functions 1-999 minute test timer vibration intensity pause time. RATING 450/750W power supply (220-240V50/60Hz1PH) Dry sieving Standard Intermittent operation At intervals Dry sieving standard Mode of operation continuous and intermittent Inter mitten operation At internals (0.5 sec) Capacity (up to 8 sieves of 50 mm height) (up to 16 sieves of 25 mm to 4 mm) Shake time programmable from 1 min to 99 min Power level programmable from 5 to 20 Display 16x2 character alphanumeric LCD Noise level (less than 61 db without sieves at maximum amplitude) (less than 71 db with sieves and material at maximum

Product Image (MTAT -02)

BRICK CUTTER

Price: 100 INR/Unit

BRICK CUTTER The offered range is suitably inspected on different parameters to ensure its compliance with the highest quality norms and standards. In addition to this, the offered range of brick cutting machines is ideally applicable for tasks such as cutting refractory brick, furnace brick, and ceramic ormosare tiles. Features Optimum performance Longer functional life Ideal for cutting clay or cement bricks Easy adjuster for brick height Light pressure for easy cutting Saving money and lifespan on your generators and grinders Extreme hard tampered steel blades for long life Replaceable blades available Having a Safety Cover Moveable Bed Technical Specification Suitable for refractoriness and lining Cut in difference angle Cut the thickness of up to 150m Power Source electric motor Power 2.4 KW Blade diameter 14 Cutting Blade Width: 16-1/8" Cutting Depth: 1-12" Motor - 7.5 hp, TEFC 415 volts /3 phase / 50 HZ Starter - DOL ( with overload relay ) Starter makereputed company Flanges- to suit above wheel Wheel guard- to suit above wheel Spindle housing ground spindle assembled in DOUBL labyrinth system.All rotating parts are dynamically balanced Panel boxMCB switch, contactor with overload RELAY,SPP,AM.METER,VOLT MTR. Other facilities belt tension device, rear splash screen, spindle lock

Product Image (MT-28033)

NIPPLE CHUCK

Price: 10 INR/Piece

NIPPLE CHUCK Microteknik are Best manufacturer and Supplier Company in India.we are Export nipple chuck in india and other place making nipples Ridged Nipple Chuck Ridged Pipe and Tubing Tools include; Ridged pipe wrench, the most complete and premier line of threading and roll grooving equipment, best-in-class pipe and tubing cutters, bending and forming tools, and a variety of other pipe working tools and accessories. Ridged 51005 NPT Nipple Chuck 1 1/2 - 2, No. 819 Features: Holds short or close nipples for threading. Holds studs for threading. For use with 300 Power Drive, 300 Compact, 535 and 1822 and 1224 threading Machines. Standard Nipple Chuck includes insert and 5 adapters: 1/2, 3/4, 1, 1 1/4 and 1 1/2.

Product Image (MTS -21176 )

Expansion Index Test Apparatus

Price: 8 INR/Piece

EXPANSION INDEX TEST APPARATUS Use: determining the expansion index of soils. Standard: ASTM D-2435, D-4546; AASHTO T-216. Specifications: Construction The unit consists of a cast aluminium base and collar, stainless steel specimen ring. Base and Collar. Cast aluminium construction; brass hold-down rods. Specimen Ring. Stainless steel; 101.6 x 25.4 mm (4" internal diam. x 1" h.). Porous Stones. 101.4 x 12.7 mm (4" diam. x 1/2" thick). Loading Weight. Brass; 5.7 kg (12.6 lbs.). Dial Indicator: 0.3" range x 0.0001" graduations. 8 mm range x 0.002 mm graduations. Test Duration. 24 hours or less on cured sample.

Product Image (MTS-27452)

Triaxial Test Set

Price: 100 INR/Unit

TRIAXIAL CELL Triaxial cell for specimens up to 70 mm diameter. Suction sleeve stretcher for 70 mm - 2.8" - 3" specimens. Membrane, rubber latex for 70 mm - 2.8" specimens (30 pieces). O-ring neoprene for 70 mm - 2.8" specimens (30 pieces). Filter drain for 70 mm specimens pack of 50. Two part split mould for 70 mm specimens SAMPLE PREPARATION Sampler for 70 mm samples piston and tube included. Rack and pinion sample extruder bench model: Allows the insertion of sampling tubes into a soil sample with a rack and pinion mechanism with minimal disturbance; it is then used to extrude the resultant sample from the sampling tube. Max. Clearance between platens: 435 mm. Min. Clearance between platens: 0 mm.

Product Image (MTS -25840)

Permeability Test System

Price: 100 INR/Piece

PERMEABILITY TEST SYSTEM Microteknik are Best manufacturer and Supplier Company in India Permeability Test System for efficient and accurate permeability testing of a wide range of construction materials Permeability Cell: Cell Diameter 75 mm. The (b) type permeability cell is specially designed for constant head tests on incoherent soil samples. It has a central body with 3 outlets for 3 manometer tubes through which water is collected after seepage through the sample. Inlet and drainage ducts are found in the metal base. A movable stem enables stabilization of the upper surface of the sample. Weight 3 Kg

Product Image (MTS-17038)

Plate Bearing Test Machine

Price: 10 INR/Piece

Plate Bearing Test Machine Microteknik Are Manufacturer And Exporter Of Plate Bearing Test Machine. For Estimating The Bearing Capacity Of Shallow Foundations In Situ And For The Design Of Flexible Pavement; Also Used For Load Tests Of Soil And Flexible Pavement Components. Specifications Of Plate Bearing Machine Pressure Gauge And Flexible Metal Pipe 5M Long - 1No. 1 Special Ball And Socket Arrangement Between The Jack And The Bearing Plate. 16 Extension Rod 12Mm. Dia X 25Cm Long. 4 Magnetic Base With Female Thread On Top For Holding Extension Rod. 4 Top End Plate, 50Mm, Dia With Male Thread For Fitting Onto The Extension Rods And Positioning The Dial Gauge Plunger. Plane M.S (Mild Steel) Plate 60 Cms X 60Cms Sq. X 25Mm Thick. Plane M.S.Plate 45Cms X 45Cm.Sq. X 25Mm Thick. Plane M.S.Plate 30Cms X 30Cm.Sq. X 25Mm Thick. 4 Dial Gauge 0.01Mm X 25Mm. Accessories. Plane M.S.Plate 50Cm X 25Mm Thick. Grooved M.S. Plate 60Cm. X 60 Cm. X 25Mm Thick, 45Cm X 45Cm X 25Mm. Thick, 30 Cm X 30Cm X 25Mm Thick, 75Cm X 75Cm X 25Mm Thick.

Product Image (MTS-101267)

Pitot Tube

Price: 10 INR/Piece

Pitot Tube: Micro Teknik Extendable (using poles provided) straight Pitot static tube. 6mm diameter, stainless steel. Straight design provides much easier access to those awkward and difficult ducts.Accessories included with the Pitot tube:1m lengths of flexible silicon tubing (2)300mm x 10mm extension poles (3)Directional pointer Instruction manual (for ST & TT series micro manometers).

Product Image (MT-16019)

Block Making Machine

Price: 100 INR/Piece

Block Making Machine Description : Block Making Machine is a device (see machine press) using a hydraulic cylinder to generate a compressive force. It uses the hydraulic equivalent of a mechanical lever. hydraulic press depends on Pascals principle: the pressure throughout a closed system is constant. One part of the system is a piston acting as a pump, with a modest mechanical force acting on a small cross-sectional area; The other part is a piston with a large area which generates a correspondingly large mechanical force. Only small-diameter tubing is needed if the pump is separated from the press cylinder. Specification : Piston diameter = 5 inch. Induction motor = 7.5 HP. Hydraulic Pump = 2. Gear Pump = 1. Plunger Pump = 1. Minimum displacement of stoke 10 inch. Three Phase supply , 440 V. Vibration Force = 100 Kn. Cycle Time = 10-18 sec. Production = 2000 - 2500 pieces in working 8 hours. Components Use : Hydraulic Piston (Plunger). Supporting Beam (Column). Vibrating Table. Pump Operating Pump. Hydraulic Pump. Base Stand. Pressure Gauge. Operating lever.

Product Image (MTS-22344)

Grain Size Chart

Price: 5 INR/Piece

GRAIN SIZE CHART Microteknik are Manufacturer company in India Soil grain chart Specifications: Grain Size Chart is widely used by field geologists for describing samples. Pocket-sized with recessed die-cut sample cavities filled with precision sieved sedimentary particles permanently mounted to the chart. Classed according to the Went worth grading system.

Product Image (MTS-901 A)

Test Sieves

Price: 10 INR/Piece

TEST SIEVE Use: for sieving soil samples Standard: ISO: 565 with tolerances to ISO 3310-1. Specifications Test Sieves, 200mm diameter brass frames with stainless steel mesh. All mesh sizes in 50mm full-height frames. Sizes 5.6mm and smaller with 25mm half-height frames. All ISO Sieves are serial numbered, supplied with certificates of quality, and include SBR rubber o-ring seals.

Product Image (MTS-109496 )

Soil Hydrometer

Price: 5 INR/Piece

Use: to determine specific gravity of soils. Standard: ASTM D-422/AASHTO T-88 Specifications: Construction: Moulded, seamless. Scale: Bouyoucos; double scale. Calibration: At 68F. Graduations: -5 to 60 g colloids/liter. scale 152H. 0.995 to 1.038 specific gravity x 0.001 divisions

Product Image (MTS-596)

CONCRETE COVER METER

Price: 10 INR/Piece

CONCRETE COVER METER Microteknik are manufacturer and Exporter of Concrete Cover Meter for Engineering testing. Specification of Concerete Cover Meter Use: Reinforcement depth measurement Bar size can be preset if known, or detected automatically for survey and investigation tasks. For non-standard bar sizes, large diameter pipes or other pre-fabricated items, it can also show absolute measurements that can be used to look up cover using custom tables. For immediate results on-site, the onscreen gauge and audio feedback rapidly pin-point rebar location and orientation. Meets or exceeds the requirements of BS1881 part 204 over the full range of the instrument Cover range 5mm š“ 185 mm Accuracy: š± 1mm up to 60mm cover š± 2mm up to 120mm š± 3mm up to 160mm š± 4mm over 160mm Automatic Bar Sizing Cover meter Includes Probe with integral cable Battery charger Spare probe sole-plate Certificate of Conformity Light & tough equipment bag

Product Image (MTS-11083)

Length Gauge

Price: 10 INR/Piece

LENGTH GAUGEUse: Used to classify aggregates as elongated when their length is more than 1.8 of their nominal size, the test is notapplicable to material retained on a 63.0 mm BS test sieve.Test app to materials retained in 63mm BS seiveStandard: EN 933-1Construction: The thickness gauge is of enameled sheet metal with clearly marked sieve fraction ranges for each slot The Length Gauge has brass pins set in a brass bar with stamped sieve fraction ranges between pins. Weight approximately 1.1 kg Thickness gauge sheet metal with seved maked fraction weigh 1.1.14

Product Image (MTS-11071)

Shrinkage Bar Mould

Price: 100 INR/Piece

SHRINKAGE MOULDMICROTEKNIK are Manufacturing company in india Linear shrinkage of cement mortar.Description: Three gang mould supplied complete with 6 shrinkage plugs. Capacity: 40x40x160 mm mortar prisms.

Product Image (MTS -17003)

Digital Point Load Tester

Price: 100 INR/Unit

DIGITAL POINT LOAD TESTER Microteknik are manufacturer and Exporter of Digital Point Load Tester for engineering training Equipment. Use: Aggregate strength

Product Image (MTS-469)

DEVIL ABBRASION TEST MACHINE

Price: 100 INR/Piece

DEVIL ABBRASION TEST MACHINE Microteknik are Sole Manufacturer and Exporter Company in india Aggregate resistance to abrasion, Rotating frame is driven by a motor/speed reducer and an automatic counter is included to preset the required number of revolutions. Specifications: Rotating frame driven by a motor/speed reducer. Automatic counter which can be to preset the required number of revolutions. Rotation speed: 33 rpm. Specimen size 4"maxi. load 0 to 56 KN.

Product Image (MTS-TBM)

TEST BAR MOULD

Price: 10 INR/Piece

TEST BAR MOULDS Use: Expansion, Soundness Specifications: Gauge Length: 254 mm (10") between inner ends of embedded contact points. Two-Gang Mold: 25.4 x 25.4 x 254 mm (1" x 1" x 10") gauge length. Single Mold: 101.6 x 101.6 x 254 mm (4" x 4" x 10") gauge length. Contact Points: 6.3mm (1/4") diam. x 19mm (3/4") long in a pack of 100.

Product Image (MTS -210034)

PLASTIC LIMIT ROLLER

Price: 10 INR/Piece

PLASTIC LIMIT ROLLER Microteknik are Best manufacturer and Supplier Company in India. Mechanical rolling to determine plastic limit Specifications: 50-sheet pad of adhesive paper, and instructions. The 4.8mm and 9.5mm (3/16in -3/8in) rigid acrylic device measures. Consists of top and bottom roller plates separated by 3.2mm (1/8in) side rails. Special adhesive-backed absorbent paper that adds no fibre to soil samples.

Product Image (MT-28026)

RIVET GUN

Price: 10 INR/Piece

RIVET GUN We are Rivet Gun Manufacturer and Suppliers Microteknik Company in India For riveting work Specification: Accepts all rivet sets and dimple die sets with .187 shank dia. Rolling cam and wedge assembly develops 3,000 lb. compression force with 90-100 PSI input. Easy changing of yokes and tooling. One man operation. Thumb trigger throttle - controls plunger speed for easy rivet setting.

Product Image (MTSD-409)

COARSE AGGREGATE DENSITY TEST SET

Price: 100 INR/Piece

COARSE AGGREGATE DENSITY TEST SET Microteknik are manufacturer and Exporter of Coarse Aggregate Density test for Engineers Training Equipment. measurement of density and specific density, standard weighing Specifications of Aggregate Density Test Set 1 Pan, Galvanized Power 220vAC, 50/60H Density Basket: with dimensions 203 mm diameter x 203 mm deep, constructed of reinforced no. 8 wire mesh). Water tank with dimensions: 400x400x330 mm approx.

Product Image (MTS -210123)

SHRINKAGE PRONG PLATE

Price: 10 INR/Piece

SHRINKAGE PRONG PLATE Use: Accessory to shrinkage limit set. Specifications: Rust-resistant construction, three rust-resistant metal prongs for immersing soil pat. Construction of Acrylic plastic with 3 metal prongs. Shrinkage Dish. Crystallizing Dish.

Product Image (MTS-11071)

SHRINKEAGE MOULD

Price: 10 INR/Piece

SHRINKAGE MOULD Use: Linear shrinkage of cement mortar. Standard: EN 1367-4; ASTM C490 Description: Three gang mould supplied complete with 6 shrinkage plugs. Capacity: 40x40x160 mm mortar prisms

Product Image (MT-16021)

Scaffold and Plateform

Price: 10 INR/Piece

SCAFFOLD & PLATFORM Specification Material: galvanized tubular steel.

Product Image (MTS -458B)

Motorized CBR Machine

Price: 100 INR/Unit

MOTORISED CBR MACHINE Use: CBR test for determining bearing capacity of soils. Standard: ASTMD-1883,AASHTO T-193 and BS 1377.

Product Image (MTS-593)

Concrete Poker Vibrator

Price: 100 INR/Unit

CONCRETE POKER VIBRATOR Microteknik are Manufacturing Company in Concrete poker vibration machine,we are Concrete poker vibration machine supplier and Exporter Compaction of concrete specimens; Alternative of tamping bar Specification: Recoil start unleaded gasoline. Direct driven output. Fuel Tank Volume 1300 ml.

Product Image (MT-28005)

STRAP WRENCH

Price: 10 INR/Piece

STRAP WRENCH MICROTEKNIK Manufacturer The Mini Strap Wrench is ideal for use on decorative finishes, faucets, shower heads and objects with irregular shapes. Specification: For items up to 2š inch outer diameter. Fabric strap with rubber-textured grip. Strap width is 5/8š for tight spaces. High strength metal handle. Opens jars, lids and bottles with ease.

Product Image (MTS-16077)

MORTAR MIXER

Price: 100 INR/Piece

MORTAR MIXER MICROTEKNIK are Sole Best Manufacturing Company in India we are supplier and Exporter Company in India Specifications: Motor: 1/6 h.p.; 124 Watts. Power: 220 š“ 240 V AC, 50 - 60 Hz, 1 ph. Speeds: Low, intermediate, and high; 139, 285 and 591 rpm. Mixing: Planetary action. Bowl: Stainless steel; with clearance adjustment bracket. Beater: Flat-type; stainless steel.

Product Image (MTS-435)

REBOUND HAMMER

Price: 10 INR/Piece

REBOUND HAMMER Use: Hardness test (Packed in a carrying case and stores on shelves) Accessories: Calibration anvil. Used for calibration of concrete test hammers. Made of alloy steel.

Product Image (MTS-16041)

Gauge Rods

Price: 10 INR/Piece

GAUGE RODS Use To ensure that the courses are equal; Used in conjunction with the datum peg to assist the bricklayer in gauging all further courses of brickwork when setting up the corner of a building. Constructed from a piece of timber. Dimensions:1 metre long and 50 x 25mm in size. The vertical spacing of the bricks marked along one edge.

Product Image (MTS -21164)

SAND GAUGE CHART

Price: 10 INR/Piece

SAND GAUGE CHART Use: A unique chart for uniform classification of sands. Standards To classify soils to BS 1377:2, ENV 1997-2, ASTM D4318, AASHTO T89 Specifications: Nine granule patches firmly attached to the handy water-resistant plastic card defining roundness and size of particles from 2mm very coarse sand to 1/16mm silt. A checklist defining bed thickness. Flip side of chart with tables of geologic age and carbonate classification information. Sample Panels. Very coarse; coarse; medium; fine; very fine; silt. Particle Shape Panels. Angular; sub-angular; sub-rounded and rounded.

Product Image (MTS-16099)

BLAINE FINENESS APPARATUS

Price: 100 INR/Unit

BLAINE FINENESS APPARATUS Microteknik Manufacturer and Supplier Exporter Company in IndiaFineness of cement Specifications Stainless steel plunger. Manometer: U-tube glass with ground joint, stop cock and rubber bulb assembly. Filter Paper: 12.70 mm diam. Manometer liquid: Dibutyl phthalate.

Product Image (MTS-16161)

BRASS RING MOULD

Price: 5 INR/Piece

BRASS RING MOULD Microteknik are Manufacturing Company in Brass ring mould Soundness of hydrated lime and gypsum plasters. Description: Three moulds: dimensions 100mm dia. X 5 mm deep with an internal taper of 5o with complete glass plate.

Product Image (MTS -21110)

Vessel Device

Price: 10 INR/Piece

VOLU VESSEL DEVICE Use: Used to determine the in-place density of compacted or firmly-bonded soils. Standard: ASTM D2167; AASHTO T205 Specifications: Graduated Cylinder. Heavy-duty plastic; dual graduated. Balloons. Resilient latex. Guard. Aluminium with integral carrying handle. Guard Base. Aluminium; with fittings, outlets, valves and vent tube for balloon and actuator bulb. Actuator Bulb. Double acting type for pressure or vacuum; fitted with adapter, quick coupler and valve assembly. Density Plate. Aluminium with flanged sides; 229x229 x 19 mm). Operating Liquid. Water. Accessories Balloons in packs of ten. Aqua-Check for moisture determinations. In-Place Density Accessory Kit.

Product Image (MTS-17032)

Core Cutter

Price: 10 INR/Piece

CORE CUTTER Microteknik are Best manufacturer and Supplier Company in India.to extract sample of the soil with the help of a dolley and rammer. Standards : ASTM D 1556; AASHTO T19; BS 1377. Specifications: Cylindrical core cutter made of steel, 127.3 mm long and 100mm internal diameter. Steel Dolley, 25 mm high with a lip to enable it to be located on top of the core cutter. Rammer with detachable steel rod. Accessories: Cylindrical core cutter 100 mm I.D. x 175 mm long. Cylindrical core cutter 100 mm I.D. x 175 mm long. Cylindrical core cutter 100 mm I.D. x 175 mm long. Test form pad of 50.

Product Image (MT-101450)

Plate Girder Bridge

Price: 100 INR/Piece

Plate Girder Bridge: A properly constructed model of usual construction showing abutment, wing walls all necessary transverse and longitudinal sleepers and track of rail rod. The model is about 135 cm long and Is made of metallic and wooden parts..... Features: Die-cast girders and track supports Highly detailed Accurately detailed bridge track Add-on kit available for multiple track mainlines Tie strip has UV additive for outside use Track 18" in length; Girders 15" in length; height of girders: 1.8" Available in both 2-Rail and 3-Rail versions

Product Image (MT-101451)

Lattice Girder Bridge

Price: 100 INR/Piece

Lattice Girder Bridge: A properly constructed model of usual construction showing abutment, wing walls, all necessary transverse and longitudinal sleepers and track of rail road. The model is about 135 cm. long and is made of metal and wood.

Product Image (MT-101452)

Lattice Bowstring Girder Bridge

Price: 100 INR/Piece

Lattice Bowstring Girder Bridge: The properly constructed model of usual construction is with all necessary transverse and longitudinal sleepers and single track of rail road. The model is about 135 cm. long and Is made of metallic and wooden parts.

Product Image (MT-101453)

Road Suspension Bridge

Price: 100 INR/Piece

Road Suspension Bridge: A properly constructed model of usual construction about 135 cm rig with piers, suspension cable, links &anchor plates.

Product Image (MTS-58)

ROBOTIC TOTAL STATIONS

Price: 100 INR/Piece

ROBOTIC TOTAL STATIONS Microteknik are Best manufacturer and Supplier Company in India Instrument comes with a complete range of powerful applications: Survey, Set-up with resection, Set out, Area 3D & volume, Remote elevation, Construction, Reference Line, Reference Arc, Grid Set Out, Column Offset, CoGo routines, Missing line measurement, Two prism offsets, Road 2D & 3D Angle measurements: Accuracy 2" (0.6 mgon) Display resolution 0.1š (0.1 mgon) Method Absolute, continuous, diametrical Compensation Quadruple axis Distance measurements: Reflectorless (Non-prism): 600 meters / 2 mm + 2 ppm Reflector (prism): 3,500 meters / 2 mm + 2 ppm Footprint: 8 x 20 mm Instrument includes: EDM technology up to 600 m reflector less, Coaxial visible laser beam,

Product Image (MT-101717)

Versatile Data Acquisition System

Price: 100 INR/Piece

Versatile Data Acquisition System Description : Versatile Data Acquisition System Offered Comes Supported By Sampling Box, Sensors And Computer And Are Interconnected Through Wire. Finding Use In Lab Working Environment, The Product Allows Connection With Different Sampling Boxes. Some Of Its Features Include Providing For Accurate And Reliable Operations, Digital Interface, Portable Size Finish, Allows For Easy Installation, Allows For Independent Working Support, Compatible With Existing Computer And Operating System.

Product Image (MT-101716)

Pitot Tube

Price: 10 INR/Piece

Pitot Tube Extendable (using poles provided) straight Pitot static tube. 6mm diameter, stainless steel. Straight design provides much easier access to those awkward and difficult ducts. Accessories included with the Pitot tube: 1m lengths of flexible silicon tubing (2)300mm x 10mm extension poles (3)Directional pointer Instruction manual (for ST & TT series micro manometers)

Product Image (MT-101433)

Planter Test Apparatus

Price: 10 INR/Piece

Planter Test Apparatus The Plantar Test Analgesia Meter for paw stimulation can be used on 12 mice, 6 rats and other animals (cats, rabbits) unrestrained when testing for narcotic drugs. Experiments are easy to perform, simply slide the test head under test subject, align the heat source via our exclusive guide light (idle state) by the attached, adjustable, angled mirror on test head to test subject and perform tests. Start, stop and reset of tests is done by either the push button on test head, front panel controls or supplied foot switch. With our exclusive idle state of the heat source one is assured of exact placement of the heat source. Tests are performed on the plantar surface by a focused, radiant heat light source. The light beam is focused to the top of the glass and creates a 4X6mm intense spot on the paw. Our method of visible light is superior to the infrared light method, since a user will not always know exactly where/when the test will start, causing false starts and conditioning of animals. A built-in timer displays reaction time in .01 second increments. The height of the glass is adjustable allowing the focal point of the light to be adjusted to stimulate other body parts if needed. A Humane cutoff timer is standard. The unit can be preset for a cutoff period, at the end of which the heat source shuts off automatically if the animal has not responded, avoiding tissue damage. Our test head does not emit , clicking or whining noises that cause preconditioning of animals prior to test as with other systems on the market. Our exclusive heated glass option eliminates the glass acting as a heat sink. This feature will eliminate the reaction time of the animals to be altered due to the fact that they are placed on cold glass allowing the possibility of delayed response time to the applied heat source. Built-in heating elements in the glass which are digitally controlled for consistent temperatures. Temperature readout and adjustment from 30-40 degrees c. for the heated base is controlled on the heated base. TAIL TEMPERATURE OPTION (T) Measurement of tail temperature at all times. Trigger temperature is automatic at the start of every test. This optional feature allows automatic preheating of the tail. To ensure experiment protocols to be precisely controlled and repeated. This feature allows the user to SET the tail temperature at start of each test is to be started at up to 75 degrees Celsius. Once that preset temperature is reached the test and the timer starts automatically and after the tail flicks the timer and light stop and the result is displayed. Readout will now show in repeatable sequence the start and end temperatures as well as test time. Features Tail Temperature optional (T) Precise Programmable digital control Humane cut-off feature, set by user Adjustable beam intensity in 1% increments Reaction is detected automatically (Tail Flick Test set-up) Manual override of all timer functions All Functions and parameters entered via key-pad Heated glass option only from IITC Foot switch - RS232 - Printer output (standard) Software - USB - (optional)

Product Image (MTS-454(c))

Compression Testing Machine

Price: 100 INR/Piece

Compression Testing Machine Compression Testing Machine Electrically-cum-hand operated. The machine embodies an Hydraulic system designed to meet the requirement of Indian Standards Specification 516-1959 for compression tests on concrete Cubes upto 5cm x 5cm x 5cm 7.06cm x 7.06cm x 7.06cm, 10cm x 10cm x 10cm and 15cm x 15cm and also concrete Cylinders upto 10 x 20cm, 15 x 30 cm height Loading Unit :- The hydraulic jack of is fixed to the base. The upper platen has got a self-aligning action and is attached to a screw, which passes thru the cross-head plate, and can be raised or lowered for initial clearance adjustment. The lower platen rests on the jackram and is positioned with the help of a centering pin. Loading is accomplished by the upward movement of the lower platen. A dust cover is provided on the jack to prevent any dust from going into the cylinder. A spacer with a centering locating pin is provided to test small specimens. The lower and upper platens of the machine are hardended , ground and polished. Guidelines are marked on the lower platen to keep the specimen coaxial with the hydraulic jack. Pumping Unit :- The motorised pumping unit, which is housed in an elegant console is of double plunger type and is driven by a single phase 220/440 Volts 50 cycles electric motor. The pumping unit is a separate unit connected to the jack by means of a Rubber Hose Pipe. A junction box is suitable fixed to connect the motor to the mains thru a push button starter.Hose Pipe. A junction box is suitable fixed to connect the motor to the mains thru a push button starter. The pumping unit is fitted with a 20 cm diam dial hydraulic Pressure Gauge with 100 division i.e. calibrated against N.C.B. Tested proving ring. A max red pointer is provided to facilitate taking readings after failure of the specimen.

Product Image (MT-101430)

Flow Channel Accessories

Price: 10 INR/Piece

Flow Channel Accessories Made of transparent Arcylic sheet.

Product Image (MTS-439)

Compaction Factor Apparatus

Price: 100 INR/Piece

Compaction Factor Apparatus The apparatus is used for determining the workability of fresh concrete, provided the maximum size of the aggregate does not exceed 38 mm. The test is particularly useful for concrete mixes of very low workability where true slump values are not reliable.

Product Image (MT-101415)

Sediment Transport Demonstration Channel

Price: 10 INR/Piece

Sediment Transport Demonstration Channel This improved version of the sediment transport teaching facility allows demonstration of the full range of bed forms that arise in a mobile bed as the flow and/or slope are increased. The channel can be used to perform most of the experiments and demonstrations usually undertaken in much larger laboratory flumes, but at much lower cost and without the need for technician back-up. The equipment is portable, and therefore may be used in the classroom as well as in the laboratory. Although too small for research applications, this demonstration flume can play a useful role in any course concerning the mechanics of open channel flow and sediment transport, including those in Departments of Civil Engineering, Geology and Physical Geography. Specification A transparent, inclinable flow channel through which water can be re-circulated by a pump over a mobile bed to demonstrate the whole range of bed forms from incipient particle movement to bed wash-out. Three different discharge rates can be selected (and measured) within the range 0.2 to 0.6 litres/sec. The channel slope can be adjusted within the range 0-10%. The working section of the channel is 1.55m long, 78mm wide and 110mm deep. The equipment is self-contained and may be bench-mounted in either the classroom or laboratory by virtue of its portability. A model undershot weir and bridge pier are included for local erosion demonstrations. A water level gauge is supplied to calibrate the overshot weir. Technical specification : Channel working section: Length: 1.55m Width: 78mm Depth: 110mm Discharge rate: 3 fixed flow rates between 0.2 and 0.6 litres/sec, selected by switch on pump Slope: 0 to 10% Sediment diameter: 0.1 to 0.3mm

Product Image (MTS-415)

Beam Testing Machine Motorised

Price: 100 INR/Piece

Beam testing machine Motorised The Flexure Strength Testing are designed to test flexural strength of concrete beams. The design provide maximum rigidity throughout their working range. The load is applied by the downward movement of the piston. A spacer is for testing different size of beams. The load is indicated on a calibrated bourdon tube type load gauge of range: 0 - 100 kN x 0.5 kN (0- 1O,000 kgf x 50 kgf). The load gauge is calibrated against National Council for Cement and Building Materials Certified Proving Ring. Testing Machines Light weight, rugged high strength frame Double action hydraulic pump Self-aligning roller assembly Hydraulic jack provided with retraction spring For testing beams of 100 x 100 x 500mm and 150 x 150 x 700mm Conforms to IS 516, BS 1881 and ASTM C 78 Two Models are available

Product Image (MTS-7)

MULTI PURPOSE TILTING LEVEL

Price: 10 INR/Piece

MULTI PURPOSE TILTING LEVEL

Product Image (MT-101409)

Deodorising Apparatus

Price: 100 INR/Unit

1 . Unit: Unit suitable for teaching/training and research into the principles of steam stripping of fatty acids from edible oils. This is a floor-standing batch processing vessel. Stainless steel and anodized aluminium support structure. Diagram in the front panel with similar distribution to the elements in the real unit. Elements in contact with the process fluid are constructed in stainless steel. Deodoriser vessel: 60 litres overall volume. 25 litres working volume. Product maximum temperature: 250 C. Electrical heating element (electric resistance), computer controlled, to heat the oil to temperatures of up to 250 C. (3KW approx). Cooling water coil for reducing the oil temperature on completion of the process. Steam distribution tube, which allows the steam/oil mixing required. Window for the process visualization. Multi-stage vacuum system, incorporating: Steam ejector. Condenser. Vacuum pump, computer controlled. Discharge pump. Polishing filter to remove any remaining particles in the finished oil. Pressure sensors. Temperature sensors. Level sensor. Sample collecting. Modes of operation: Deodorising: The oil is heated under vacuum using direct steam to provide the agitation for good heat transfer. When the desired pressure and temperature are achieved, the direct steam injection is adjusted to impart a high degree of turbulence to the oil, ensuring good physical contact of the steam with the oil. The impurities are carried over in the steam and condensed in the vacuum condenser, the resulting condensate blending with the vacuum pump sealant to be discharged to drain. Polishing: After deodorisation, the oil refining process is complete. The oil must therefore be free of any contaminants. For this, it is pumped through a polishing filter which removes those particles, giving a bright oil as product. The complete unit includes as well: Advanced Real Time SCADA and PID Control. Open Control + Multicontrol + Real Time Control. Own Control Software based on Labview. National Instruments Data Acquisition board (250 KS/s (kilo samples per second)). Calibration exercises included. Students multipost (an entire class) by using a projector. Ready for doing applied research, real industrial simulation, training courses possibilities, etc. Unit is totally safe (Mechanical, Electronic/Electrical and Software safety devices included). Results calculation and analysis software (CAL). Several future expansions, as ESN. Scada-Net System (many students working simultaneously), and more. Designed and manufactured under several quality standards.

Product Image (MTS -461(a))

SHEAR MACHINE

Price: 100 INR/Piece

SHEAR MACHINE Microteknik are Best manufacturer and Supplier Company in India electromechanical operating device comprising a stepper motor, a precision made reduction unit and final worm screw with reduced play. These devices are designed to obtain linear, micrometrical movements at constant speed and, independently from force developed, fast reverse drive. Noise levels are virtually imperceptible and no maintenance is required. Continual drive speed in either direction can be varied via the electronic control unit from 0.00001 to 12 mm/minute. RS232 Interface for PC. Graphic display. The number of cycles, forward/reverse speeds and displacement for the measurement of residual shear may also be programmed. Instructions

Product Image (MTS-110301)

Motorised Casangarnde Equipment

Price: 100 INR/Unit

MOTORISED CASANGARNDE EQUIPMENT Use: Measuring liquid limit Standard: ASTM D4318 1/AASHTO T 89 Specifications: Gear Motor: Attached to metal base; enclosed in housing with on-off switch. Counter: Mechanical; records number of cup drops. Cup. Spun brass; pin and slot mounting. Base. Molded hard rubber. Cam. Molded, self-lubricating plastic. Housing. Aluminum; holds cup and drop adjustment parts. Power requirements 220v AC, 50 Hz. Grooving Tools.

Product Image (MTS-67F)

Triple Prism Set

Price: 100 INR/Unit

TRIPLE PRISM SET Microteknik are Best manufacturer and Supplier Company in India Accessory for total station and theodolite. Specifications: To be compatible with theodolite/total station. Zero constant, with target. Supplied with carrying plastic container.

Product Image (MTS-17030)

Soil Volume Change Meter

Price: 100 INR/Unit

Soil Volume Change Meter Use: Measures both shrinkage and swelling of soils. Standard: BS 812, ASTM D4944, AASHTO T217 Specifications: Mould Assembly Includes porous stones and loading cap. Proving Ring 4.5 kN (1,000 lb.) capacity; dial indicator. Other Components Loading pistons; compaction hammer. Specimen Ring 70 mm (2-3/4") diam. Sample Size 10 teaspoons. Water Required 140g (5 oz.) Charts Convert readings to lbs./sq. ft. and then to PVC (Potential Volume Change) rating.

Product Image (MTS-59C)

GPS Reciever

Price: 10 INR/Piece

GPS RECEIVER Microteknik are Best manufacturer and Supplier Company in India to obtain altitude and X-Y positions Specifications: Receiver type: L1 (C/A) Channels: 20 channel all-in-view tracking Update rate: 1 Hz Autonomous: 5 m DGPS: 13 m Cold start time: 45 sec average Warm start time: 30 sec average Hot start time: 1 sec average Reacquisition: 0.1 sec average Accessories included: Telescopic Carbon Fibre and aluminium pole. Extends to 2.5m. AC adaptor, USB cable, Protective film, Hand strap, Quick start guide, Battery & pen.

Product Image (MTS-22321)

Shrinkage Limit Set

Price: 10 INR/Piece

SHRINKAGE LIMIT SET Use: Performing shrinkage limit tests Standard: BS 1377:2, EN 1997-2 The set comprises: 1 Shrinkage Dish. 1 Crystallizing Dish. 1 Shrinkage Prong Plate. 1 25 ml Graduated Cylinder. 1 Evaporating Dish. Dish.

Product Image (MTS-548)

Slump Test Apparatus

Price: 10 INR/Piece

SLUMP TEST APPARATUS We are Best manufacturer and Exporter of Civil Engineering Lab Equipment, Engineering lab Equipment for Teaching, Educational Equipment for Training, civil lab equipment for engineering college, School and universities, Specifications: Slump cone of internal dimensions 200mm. dia at base 100mm. top dia. and 300mm height. Tamping Rod made of Steel, 600 mm long x 16 mm dia. Hemispherical at both ends. Metal tray 600 x600 x80 mm. Aluminium scoop.

X


Back to top